평생사용 할려고 직접 만들었습니다만, 불경기가 뭔지... 비상금을 쥐고
있을려고 판매합니다.
거래방법은 서로 신용거래가 가능하도록 소리전자에 위탁판매
코자 합니다.
(소리전자에 가셔서 직접 물건을 보시거나, 택배 구매시에도
소리전자의 통장에 대금 입금 후 소리전자에서 제품을 택배 발송
조치한다면.... 서로간에 불신을 갖는 일이 없으리라 생각합니다.)
** 판매가격은 35만원이며, 소리전자에 문의 바랍니다.
** 12AX7 SRPP 구성 (초단관은 EI OLD관으로 교체: 음색/재생대역이 우수)
** 4.5와트+4.5와트
** 신규 제작비는 유첨 PDF파일 참조 바람 (약 64만원 소요)
** 정류관 5AR4를 사용하였으며, 초단 12AX7은 히터 직류점화
** 입력 3계통 (RCA 2계통 + RJ-45 미니잭 입력)으로 인티앰프로 사용 가능
** 평생 사용하고자 예산을 무시하고 고급 부품을 사용하여 정성껏 제작하였습니다.
** 08년 중반에 제작하여 에이징 왼료된 상태며, 최상의 콘디션 유지중.
** 신호입력 1 & 2에 일본 오야이데 인터선재 적용
** 커플링 콘덴서는 얀젠 수퍼리어 적용, 바이패스 콘덴서도 아톰 스프라그와
리파 고신뢰 콘덴서 적용
** 사용된 저항류는 로더스타인(독), PRP(미), DALE(미) 및 키와메(일) 저항 사용
** 전해콘덴서는 아톰 스프라그와 니치콘(일) 사용
** 사용된 셀렉터도 미국 C&K 밀폐형 금도금 제품으로 고급 프리앰프 제작에
사용할 목적으로 구입했던 부품을 아낌없이 적용했습니다.
** 접지 처리는 전위차를 최소화하기 위하여 회로도 대로 배치하였습니다.
초단/출력단/전원단/히터단 등 접지 처리를 어디에 어느 순서로 하느냐에
따라 재생되는 음질의 순도 역시 달라질 수 있습니다.
이론 및 try-and-error로 6bq5싱글 및 pp amp 자작을 통해 최적화된
그라운드 처리 순서로 작업하였습니다.
** 싱글앰프를 꼭 풀레인지 스피커에 물려야 제소리가 나온다는 것은 어불성설입니다.
물론 출력에 따른 구동력도 필요하겠지만, 가급적 저출력에도 기동 가능한
고급 스피커에 물리시기 바랍니다. 그 차이가 느껴 지실겁니다.
스캔스픽 유닛 급 이상을 사용한 스피커에 물리시면 귀로 그 차이가 판별이 가능합니다.
** 소리전자의 앰프/키트 제작란을 참조하시기 바랍니다.
제작원가가 올라가지만, 소켓가이드와 골드핀 지지대를 사용했습니다.
초단 12ax7 DC점화
마크레빈슨 수리용 스페어파트라고 해서 적용 콘덴서 작동범위로 -40도/+125도 콘덴서 본적있나요??? 판매자왈 롱라이프 부품이 아닌 진짜 long life라고 적혀 있습니다.
미터당 6000원인 오디언스 배선재로 작업
[[ SRPP 회로구성에 대해 설명 드립니다 ]]
==> SRPP of 12AX7 초단 구성
Basically SRPP is anode follower with constant current source as the load
instead of resistance such as anode follower in general.
Comparing to general anode follower SRPP offers some advantages such as :
a) Constant current source will provide high impedance to let the circuit achieve
higher gain than it could get with resistor as the load.
b) Constant current source help the circuit to reduce all noise and hum from power line.
c) Beside work as anode load the constan current source also perform as
cathode follower that provides low output impedance to drive low impedance load .
<< Heater regulation >>
The application of high quality regulator for heater is also important,
because all noise appears on the filament could induct into the cathode and then
appears on the output.
<< Components >>
Finally component have to be considered as one of important think that determine the
final quality of the design.
Strong phylosophy will not work without high quality components.
Due to above main reasons, SRPP of 12AX7 shows natural sound and more clean images comparing than anode follower circuit.
The circuit will perform as pure SRPP and totally the music signal will pass through
2 stage, the lower tube as anode follower and the upper tube as cathode follower.
Through high impedance output the circuit will perform as anode follower
with constant current load and totally the music signal will pass through
one stage only.
The fewer component on the signal path the better sound quality it will be.
있을려고 판매합니다.
거래방법은 서로 신용거래가 가능하도록 소리전자에 위탁판매
코자 합니다.
(소리전자에 가셔서 직접 물건을 보시거나, 택배 구매시에도
소리전자의 통장에 대금 입금 후 소리전자에서 제품을 택배 발송
조치한다면.... 서로간에 불신을 갖는 일이 없으리라 생각합니다.)
** 판매가격은 35만원이며, 소리전자에 문의 바랍니다.
** 12AX7 SRPP 구성 (초단관은 EI OLD관으로 교체: 음색/재생대역이 우수)
** 4.5와트+4.5와트
** 신규 제작비는 유첨 PDF파일 참조 바람 (약 64만원 소요)
** 정류관 5AR4를 사용하였으며, 초단 12AX7은 히터 직류점화
** 입력 3계통 (RCA 2계통 + RJ-45 미니잭 입력)으로 인티앰프로 사용 가능
** 평생 사용하고자 예산을 무시하고 고급 부품을 사용하여 정성껏 제작하였습니다.
** 08년 중반에 제작하여 에이징 왼료된 상태며, 최상의 콘디션 유지중.
** 신호입력 1 & 2에 일본 오야이데 인터선재 적용
** 커플링 콘덴서는 얀젠 수퍼리어 적용, 바이패스 콘덴서도 아톰 스프라그와
리파 고신뢰 콘덴서 적용
** 사용된 저항류는 로더스타인(독), PRP(미), DALE(미) 및 키와메(일) 저항 사용
** 전해콘덴서는 아톰 스프라그와 니치콘(일) 사용
** 사용된 셀렉터도 미국 C&K 밀폐형 금도금 제품으로 고급 프리앰프 제작에
사용할 목적으로 구입했던 부품을 아낌없이 적용했습니다.
** 접지 처리는 전위차를 최소화하기 위하여 회로도 대로 배치하였습니다.
초단/출력단/전원단/히터단 등 접지 처리를 어디에 어느 순서로 하느냐에
따라 재생되는 음질의 순도 역시 달라질 수 있습니다.
이론 및 try-and-error로 6bq5싱글 및 pp amp 자작을 통해 최적화된
그라운드 처리 순서로 작업하였습니다.
** 싱글앰프를 꼭 풀레인지 스피커에 물려야 제소리가 나온다는 것은 어불성설입니다.
물론 출력에 따른 구동력도 필요하겠지만, 가급적 저출력에도 기동 가능한
고급 스피커에 물리시기 바랍니다. 그 차이가 느껴 지실겁니다.
스캔스픽 유닛 급 이상을 사용한 스피커에 물리시면 귀로 그 차이가 판별이 가능합니다.
** 소리전자의 앰프/키트 제작란을 참조하시기 바랍니다.
제작원가가 올라가지만, 소켓가이드와 골드핀 지지대를 사용했습니다.
초단 12ax7 DC점화
마크레빈슨 수리용 스페어파트라고 해서 적용 콘덴서 작동범위로 -40도/+125도 콘덴서 본적있나요??? 판매자왈 롱라이프 부품이 아닌 진짜 long life라고 적혀 있습니다.
미터당 6000원인 오디언스 배선재로 작업
[[ SRPP 회로구성에 대해 설명 드립니다 ]]
==> SRPP of 12AX7 초단 구성
Basically SRPP is anode follower with constant current source as the load
instead of resistance such as anode follower in general.
Comparing to general anode follower SRPP offers some advantages such as :
a) Constant current source will provide high impedance to let the circuit achieve
higher gain than it could get with resistor as the load.
b) Constant current source help the circuit to reduce all noise and hum from power line.
c) Beside work as anode load the constan current source also perform as
cathode follower that provides low output impedance to drive low impedance load .
<< Heater regulation >>
The application of high quality regulator for heater is also important,
because all noise appears on the filament could induct into the cathode and then
appears on the output.
<< Components >>
Finally component have to be considered as one of important think that determine the
final quality of the design.
Strong phylosophy will not work without high quality components.
Due to above main reasons, SRPP of 12AX7 shows natural sound and more clean images comparing than anode follower circuit.
The circuit will perform as pure SRPP and totally the music signal will pass through
2 stage, the lower tube as anode follower and the upper tube as cathode follower.
Through high impedance output the circuit will perform as anode follower
with constant current load and totally the music signal will pass through
one stage only.
The fewer component on the signal path the better sound quality it will be.